loading

CTECHI is an expert in battery solutions, specializing in ODM, OEM, and SKD for energy storage, motive power, and consumer batteries.

What should I do if the lithium battery protection board has no display, low output voltage, and no load?

With the rapid development of the electric industry, the lithium battery protection board industry has also entered a glorious moment. This is not only an opportunity for the lithium battery protection board industry, but also a challenge for the lithium battery protection board industry. Lithium battery protection boards are becoming more and more popular in life. It can be said that they are everywhere and exist all the time (such as mobile phones, electric cars, electric toys, etc.). As a result, the technology of lithium battery protection board industry becomes more and more challenging. The higher you come, today, the Chinese Chuangfa will learn with everyone what to do if the lithium battery protection board has no display, low output voltage, and no load.

Don’t panic when encountering such unfavorable conditions. First, eliminate the bad battery (the battery is originally without voltage or the voltage is low). If the battery is bad, you should test the protection board. Self-consumption, to see if the self-consumption of the protection board is too large and the battery cell voltage is low. If the battery voltage is normal, it may be due to the failure of the entire circuit of the protection board (components soldering, false soldering, bad FUSE, PCB board internal Circuit failure, via failure, MOS, IC damage, etc.). The specific analysis steps are as follows: (1). Connect the black test lead of a multimeter to the negative electrode of the battery, and connect the red test lead to the FUSE and R1 resistor ends, the Vdd, Dout, and Cout terminals of the IC, and the P+ terminal (assuming electric The core voltage is 3.8V), analyze it section by section, and these test points should all be 3.8V. If not, there is a problem with this section of the circuit.

1. There is a change in the voltage across the FUSE: test whether the FUSE is turned on, if it is turned on, the internal circuit of the PCB board is not turned on; if it is not turned on, the FUSE has a problem (bad incoming material, overcurrent damage ( MOS or IC control failure), there is a problem with the material (the FUSE is burned out before the MOS or IC is activated), then use a wire to short the FUSE, and continue to analyze.

2. There is a voltage at both ends of the R1 resistor. Change: Test the resistance value of R1. If the resistance value is abnormal, it may be a virtual weld and the resistance itself is broken. If the resistance value is not abnormal, there may be a problem with the internal resistance of the IC.

3. IC test terminal voltage Change: The Vdd terminal is connected to the R1 resistor. The Dout and Cout terminals are abnormal, because the IC is soldered or damaged.

4. If there is no change in the previous voltage, test the abnormal voltage between B- and P+ , It is because the positive through hole of the protection board is blocked.

(2) Connect the red test lead of the multimeter to the positive electrode of the battery cell. After activating the MOS tube, the black test lead is connected to the MOS tube 2, 3, 6, 7 in turn. , P-terminal.

1. If the voltage of MOS tube 2, 3, 6 and 7 has changed, it means the MOS tube is abnormal.

2. If the MOS tube voltage does not change If the P-terminal voltage is abnormal, it is because the negative via of the protection board is blocked.

The lithium battery industry chain is promoted by enterprises in the lithium battery industry chain, and the lithium grid (li-b.cn) welcomes contributions. Share:

GET IN TOUCH WITH Us
recommended articles
Services 200 FAQs Case
ElonMusk, the hottest geek in the automobile industry, this madman in the scientific world is almost paranoid about technology and won the name of the real Iron Man.
The large-scale development of lithium-ion batteries puts forward new requirements for production and manufacturing.
On the eve of the explosion of the global new energy industry, power lithium battery manufacturing moved from GWh to TWh.
Tesla's official website updated its Model Y promotional page on January 1, announcing that the Model Y pricing has been significantly reduced.
Recently, due to the strong market demand, the power battery industry chain has 'exploded ordersAccording to the company's data, as of January 2021, there were 18,000 power battery-related companies in my country.
According to foreign media reports, electric vehicles are driven by rechargeable lithium-ion batteries (LIb), but at present, people have not fully understood and perfected lithium-ion batteries.
At the Frankfurt Motor Show, Honda also announced the mass production version of HondaE, and also announced the two-way connection system HondaPowerManagerPrototype for EVs and smart grids.
Introduction: An electric car company and a business park operator in Florida have pledged to invest up to US$1 billion in the planned plant in Chonburi, starting with the 1GWh portion that may take shape in 2023.
The topic of electrification and national geopolitics sounds very grand at first, and you can write a long and long narrative, of course, you can also make a long story short.
With the limelight of new energy vehicles, CATL has become one of the most shining companies in this tuyere.
no data
no data
no data
Copyright © 2025 CTECHI | Sitemap | Privacy Policy
Customer service
detect